Generic hull coupled roll screening estimate

Generic hull roll-plus-tank screening estimate from a public coupled model.

Engineering screening analysis · generic normalized hull

1 Executive summary

The coupled model can be used to compare generic hull roll with and without the connected tank. The results are screening estimates; no result represents a real hull.

The implications of the model's stated moment fit are listed in Section 7.

Peak roll reduction against alpha Peak roll reduction (%) against Alpha: normalized stiffness (dimensionless). Hull damping 2 %; Hull damping 5 %. Peak roll reduction against alpha 0 20 40 60 80 0.00 0.05 0.10 0.15 0.20 Alpha: normalized stiffness (dimensionless) Peak roll reduction (%) Hull damping 2 % Hull damping 2 %: 0.02, 24.2533874028 Hull damping 2 %: 0.05, 46.1131587008 46.1 % Hull damping 2 %: 0.1, 61.3708265831 Hull damping 2 %: 0.15, 65.9955703766 Hull damping 2 %: 0.2, 67.1972659743 Hull damping 5 % Hull damping 5 %: 0.02, 10.4739692338 Hull damping 5 %: 0.05, 23.2862649764 23.3 % Hull damping 5 %: 0.1, 37.8622654351 Hull damping 5 %: 0.15, 45.5813812497 Hull damping 5 %: 0.2, 48.6884412365 outside the model's moment-fit band (forcing period below 20 s)
Figure 1.1 – Peak roll reduction against alpha at an 18 s hull roll period, 2 % and 5 % hull damping, with the alpha 0.05 results marked.
Export CSV

Figure 5.3 data: Figure 5.3. Source: [I1]. Chart notes in Appendix A.

Connected anti-roll tank, three-dimensional view Axonometric view with proportional recorded leg length, width, fill depth and centroid offset. Hull form, tank height above fill and conduit section are symbolic; conduit area is a recorded label. Tank leg 1 Tank leg 2 symbolic hull, no hull dimensions
Figure 1.2 – The connected anti-roll tank in a generic hull, three-dimensional view (detail in Figure 3.2).

2 Introduction

The generic hull roll comparison describes the effect of a connected anti-roll tank for engineers considering the simplified coupled model. The scope is a normalized hull and the public reference tank, with no actual hull mass, inertia or restoring.

These screening estimates exclude sea-state weighting, structural loads and design qualification. No full-scale roll reduction has been calculated here.

3 Design data

The calculation uses public reference tank inputs (ASSUMED - to be confirmed), with no actual hull geometry. The input values and their units are listed in Table 3.1.

3.1 Site or field data

Not applicable: no site or field is represented.

3.2 Structure or equipment data

Each leg measures 20.0 m by 6.0 m (120 m² in plan). Fill depth is 5.0 m; centroid offset is 5.0 m. Conduit area A_c is 6.8 m². The model supplies effective length, fluid properties and calibrated loss parameters.

InputValueUnitBasis
Each leg length20mASSUMED; [I1]
Each leg width6mASSUMED; [I1]
Fill depth5mASSUMED; [I1]
Centroid offset5mASSUMED; [I1]
Conduit area6.8m²ASSUMED; [I1]
Effective conduit length5.2mASSUMED; [I1]; [I2]
Fluid density1025kg/m³ASSUMED; [I1]; [I2]
Gravity9.81m/s²ASSUMED; [I1]; [I2]
Loss coefficient2.389m^(2n−4)ASSUMED; [I1]; [I2]
Loss area exponent n2.1381ASSUMED; [I1]; [I2]
Bare-roll reference5°ASSUMED; [I1]
Normalized hull restoring11ASSUMED; [I1]
Table 3.1 – Recorded tank and normalized-hull inputs.

The recorded inputs are illustrated by Figure 3.1 and Figure 3.2.

In the loss-coefficient unit, n is the loss area exponent in Table 3.1.

Calibration transfer means using the model's calibrated loss parameters in this reference-tank and generic-hull calculation: ASSUMED - to be confirmed. These screening estimates use the public reference tank, which differs from the illustrative tank on the linked study page [I3].

The transverse leg widths, fill depths and centroid offsets in Figure 3.1 use the dimensions in Table 3.1. Tank dimensions are recorded assumptions; the hull outline supplies no hull dimensions.

Hull section with U-tube anti-roll tank Proportional transverse leg widths, fill depths and centroid offsets from Table 3.1. Hull outline and conduit height are symbolic; no hull dimensions are supplied. U-tube anti-roll tank · transverse section φ (roll) Oscillatory flow Leg width 6.0 m Offset 5.0 m Fill 5.0 m Centreline A_c 6.8 m² Symbolic duct height Leg length 20.0 m (out of section) · dimensions ASSUMED Hull section: outline and duct height not to scale
Figure 3.1 – Connected-tank transverse section.

Figure 3.2 shows the same recorded tank dimensions in three dimensions.

Connected anti-roll tank, three-dimensional view Axonometric view with proportional recorded leg length, width, fill depth and centroid offset. Hull form, tank height above fill and conduit section are symbolic; conduit area is a recorded label. Tank leg 1 Tank leg 2 Each leg length 20.0 m Each leg width 6.0 m Fill depth 5.0 m Centroid offset 5.0 m Conduit area 6.8 m² Free surface in each leg Roll axis Transverse Longitudinal Vertical Tank height above fill: symbolic Conduit height: symbolic Conduit section shape: symbolic symbolic hull, no hull dimensions
Figure 3.2 – Connected anti-roll tank, three-dimensional view: the two legs, the fill, the cross-connecting conduit and the generic hull section around them.

3.3 Environmental data

No sea state is specified. Forcing stays fixed within each tank-on and tank-off comparison and is rescaled between damping groups.

3.4 Vessel data

Generic hull periods are 18 s and 21 s; hull damping is 2 % and 5 % of critical, and alpha is 0.02, 0.05, 0.10, 0.15 and 0.20. All hull values are ASSUMED; no real hull data is used. The full load-case matrix is in Appendix A.

3.5 Criteria and sources

No design acceptance criterion is specified. The arithmetic checks and the model's stated moment-fit band are distinguished in Section 6. Their sources are [I4] and [R1].

3.6 Load cases

Every combination of the assumed hull periods, damping and alpha values is retained in Table A.1. The response sweep covers 0.7 to 1.3 times each hull period; the additional long-period comparison uses 60 s forcing [I1].

4 Analysis methodology

The model links hull roll to water transfer between connected tank legs. Tank moments feed back into the hull roll equation. Alpha is the tank's quasi-static free-surface moment stiffness divided by the hull's roll restoring. Alpha is dimensionless.

The public U-tube model is used; a software version is not declared. Its exact source is identified in [I2]. Kₛ is the quasi-static tank moment per roll angle. The public model includes vertical-centroid and local free-surface terms in Kₛ. Kₛ also includes water redistribution between the legs. Alpha therefore follows the complete public moment convention.

(4.1) The normalized bare-hull impedance is D = 1 − (T₀/T)² + 2iζ(T₀/T).

(4.2) The coupled impedance is D − αH/Kₛ. H is tank moment per roll angle; Kₛ is its quasi-static limit.

T₀ is the hull roll period (s), T is the forcing period (s), ζ is the hull damping ratio (1), and i is the imaginary unit. H and Kₛ use the same moment-per-angle units, so both impedances and alpha are dimensionless [I2].

The hull equation uses normalized restoring of 1, with no units. The model sets forcing to give 5° bare roll at the nominal resonance (ASSUMED - to be confirmed). Forcing stays fixed within each tank-on and tank-off comparison. Forcing is rescaled between damping groups to keep the 5 degree bare-roll reference, so the comparison also changes the tank amplitude.

The calculation finds each response peak separately over 0.7 to 1.3 times the hull roll period. Reduction equals 100 % times one minus the coupled peak divided by the bare peak. The input basis and calculation are recorded in [I1] and [I4].

5 Results

All charts select the existing 18 s hull roll period and conduit area 6.8 m². The wave-period chart uses 2 % hull damping and alpha 0.05. Alpha is normalized stiffness as defined in Section 4. The calculated tank natural period is 14.3 s [I4]. The reference geometry is retained rather than tuned to the 18 s hull; the tank and hull natural periods therefore differ.

5.1 Peak roll reduction

Figure 5.1 shows peak reduction against hull damping; Figure 5.2 shows the dimensionless roll amplification factor against forcing period; Figure 5.3 shows peak reduction against alpha. The full sensitivity matrix and damping comparison are in Appendix A.

The amplification factor multiplies the normalized wave moment to give roll in radians. The bare factor is 1/(2ζ) at the nominal hull resonance; a normalized moment of 2ζ times 5° in radians gives the 5° bare roll used here.

Peak roll reduction against hull damping Peak roll reduction (%) against Hull damping (% of critical). Alpha 0.05. Peak roll reduction against hull damping 0 10 20 30 40 50 2 3 4 5 Hull damping (% of critical) Peak roll reduction (%) Alpha 0.05 Alpha 0.05: 2.0, 46.1131587008 Alpha 0.05: 5.0, 23.2862649764
Figure 5.1 – Peak roll reduction against hull damping.
Export CSV

Source: [I1]. Chart notes in Appendix A.

Roll response with and without the tank Roll amplification factor (dimensionless) against Wave forcing period (s). Without tank; With tank. Shaded periods are outside the model's stated moment-fit band. Roll response with and without the tank 0 5 10 15 20 25 10 15 20 25 Wave forcing period (s) Roll amplification factor (dimensionless) Without tank Without tank: 12.6, 0.959339568804 Without tank: 12.69, 0.986620910235 Without tank: 12.78, 1.01487266036 Without tank: 12.87, 1.04414518618 Without tank: 12.96, 1.0744924181 Without tank: 13.05, 1.10597216947 Without tank: 13.14, 1.13864649106 Without tank: 13.23, 1.172582065 Without tank: 13.32, 1.20785064331 Without tank: 13.41, 1.24452953711 Without tank: 13.5, 1.28270216338 Without tank: 13.59, 1.32245865735 Without tank: 13.68, 1.36389655982 Without tank: 13.77, 1.40712159024 Without tank: 13.86, 1.45224851847 Without tank: 13.95, 1.49940214978 Without tank: 14.04, 1.54871844101 Without tank: 14.13, 1.60034576822 Without tank: 14.22, 1.65444637052 Without tank: 14.31, 1.71119799902 Without tank: 14.4, 1.77079580568 Without tank: 14.49, 1.83345451325 Without tank: 14.58, 1.89941091649 Without tank: 14.67, 1.9689267743 Without tank: 14.76, 2.04229216582 Without tank: 14.85, 2.11982939884 Without tank: 14.94, 2.20189757874 Without tank: 15.03, 2.2888979708 Without tank: 15.12, 2.38128031986 Without tank: 15.21, 2.47955033075 Without tank: 15.3, 2.5842785634 Without tank: 15.39, 2.69611106101 Without tank: 15.48, 2.81578211333 Without tank: 15.57, 2.94412966556 Without tank: 15.66, 3.0821140253 Without tank: 15.75, 3.23084070723 Without tank: 15.84, 3.39158850327 Without tank: 15.93, 3.56584419761 Without tank: 16.02, 3.75534579213 Without tank: 16.11, 3.96213671206 Without tank: 16.2, 4.18863428609 Without tank: 16.29, 4.43771692548 Without tank: 16.38, 4.71283598454 Without tank: 16.47, 5.01816043672 Without tank: 16.56, 5.35876547051 Without tank: 16.65, 5.74088017775 Without tank: 16.74, 6.17221497915 Without tank: 16.83, 6.66239649236 Without tank: 16.92, 7.22354583301 Without tank: 17.01, 7.87104372379 Without tank: 17.1, 8.62452515742 Without tank: 17.19, 9.50911710772 Without tank: 17.28, 10.5568187714 Without tank: 17.37, 11.8075776138 Without tank: 17.46, 13.3086646285 Without tank: 17.55, 15.108539339 Without tank: 17.64, 17.2359544034 Without tank: 17.73, 19.6460171194 Without tank: 17.82, 22.1146898249 Without tank: 17.91, 24.1287243025 Without tank: 18.0, 25.0 Without tank: 18.09, 24.3783933614 Without tank: 18.18, 22.6066250035 Without tank: 18.27, 20.3540153205 Without tank: 18.36, 18.119826827 Without tank: 18.45, 16.1274475998 Without tank: 18.54, 14.4286728667 Without tank: 18.63, 13.0029841984 Without tank: 18.72, 11.8088736334 Without tank: 18.81, 10.8042724301 Without tank: 18.9, 9.95295160723 Without tank: 18.99, 9.22553359803 Without tank: 19.08, 8.59874233285 Without tank: 19.17, 8.05426096387 Without tank: 19.26, 7.57765886851 Without tank: 19.35, 7.1575089695 Without tank: 19.44, 6.78469860225 Without tank: 19.53, 6.4519030598 Without tank: 19.62, 6.15318644863 Without tank: 19.71, 5.88369916516 Without tank: 19.8, 5.639447781 Without tank: 19.89, 5.41711900473 Without tank: 19.98, 5.21394408953 Without tank: 20.07, 5.02759362203 Without tank: 20.16, 4.8560952659 Without tank: 20.25, 4.69776896565 Without tank: 20.34, 4.55117552605 Without tank: 20.43, 4.41507551291 Without tank: 20.52, 4.28839617589 Without tank: 20.61, 4.17020465098 Without tank: 20.7, 4.05968611282 Without tank: 20.79, 3.95612585471 Without tank: 20.88, 3.85889450545 Without tank: 20.97, 3.76743576715 Without tank: 21.06, 3.68125619066 Without tank: 21.15, 3.59991660787 Without tank: 21.24, 3.52302491816 Without tank: 21.33, 3.45022998767 Without tank: 21.42, 3.38121646743 Without tank: 21.51, 3.31570037396 Without tank: 21.6, 3.25342530526 Without tank: 21.69, 3.19415918884 Without tank: 21.78, 3.13769147689 Without tank: 21.87, 3.08383071891 Without tank: 21.96, 3.03240245404 Without tank: 22.05, 2.9832473753 Without tank: 22.14, 2.93621972586 Without tank: 22.23, 2.89118589393 Without tank: 22.32, 2.8480231783 Without tank: 22.41, 2.80661870088 Without tank: 22.5, 2.76686844637 Without tank: 22.59, 2.72867641198 Without tank: 22.68, 2.69195385299 Without tank: 22.77, 2.65661861158 Without tank: 22.86, 2.62259451872 Without tank: 22.95, 2.58981085978 Without tank: 23.04, 2.55820189622 Without tank: 23.13, 2.52770643665 Without tank: 23.22, 2.49826745139 Without tank: 23.31, 2.46983172543 Without tank: 23.4, 2.44234954555 With tank With tank: 12.6, 1.02750115441 With tank: 12.69, 1.05706946032 With tank: 12.78, 1.08685007792 With tank: 12.87, 1.11675313454 With tank: 12.96, 1.14670725018 With tank: 13.05, 1.17666313825 With tank: 13.14, 1.20659530508 With tank: 13.23, 1.23650215419 With tank: 13.32, 1.2664049898 With tank: 13.41, 1.296346379 With tank: 13.5, 1.32638824218 With tank: 13.59, 1.35660992654 With tank: 13.68, 1.38710641312 With tank: 13.77, 1.41798673466 With tank: 13.86, 1.44937261428 With tank: 13.95, 1.48139733324 With tank: 14.04, 1.51420479478 With tank: 14.13, 1.5479487667 With tank: 14.22, 1.58279228363 With tank: 14.31, 1.61890720011 With tank: 14.4, 1.65647389327 With tank: 14.49, 1.69568112442 With tank: 14.58, 1.73672609078 With tank: 14.67, 1.77981466959 With tank: 14.76, 1.8251619214 With tank: 14.85, 1.87299286398 With tank: 14.94, 1.92354361363 With tank: 15.03, 1.97706283676 With tank: 15.12, 2.03381367901 With tank: 15.21, 2.09407619887 With tank: 15.3, 2.15815024143 With tank: 15.39, 2.22635900642 With tank: 15.48, 2.29905322555 With tank: 15.57, 2.37661618877 With tank: 15.66, 2.45946948062 With tank: 15.75, 2.54807984801 With tank: 15.84, 2.64296724832 With tank: 15.93, 2.74471413047 With tank: 16.02, 2.85397651554 With tank: 16.11, 2.97149695866 With tank: 16.2, 3.09812000557 With tank: 16.29, 3.23481035002 With tank: 16.38, 3.38267466372 With tank: 16.47, 3.5429875354 With tank: 16.56, 3.71722260206 With tank: 16.65, 3.90708947321 With tank: 16.74, 4.1145778277 With tank: 16.83, 4.34200938447 With tank: 16.92, 4.59209793697 With tank: 17.01, 4.86801736123 With tank: 17.1, 5.17347401951 With tank: 17.19, 5.51277646199 With tank: 17.28, 5.89088572407 With tank: 17.37, 6.3134127859 With tank: 17.46, 6.78649976894 With tank: 17.55, 7.31646901212 With tank: 17.64, 7.90903895363 With tank: 17.73, 8.56778975672 With tank: 17.82, 9.29145217433 With tank: 17.91, 10.0696610437 With tank: 18.0, 10.877461604 With tank: 18.09, 11.670641733 With tank: 18.18, 12.3866274451 With tank: 18.27, 12.9561775309 With tank: 18.36, 13.3246595499 With tank: 18.45, 13.4709442963 With tank: 18.54, 13.4107793279 With tank: 18.63, 13.1845144289 With tank: 18.72, 12.8402407975 With tank: 18.81, 12.421747174 With tank: 18.9, 11.9633812789 With tank: 18.99, 11.4896251399 With tank: 19.08, 11.0167551415 With tank: 19.17, 10.5549555317 With tank: 19.26, 10.1101797409 With tank: 19.35, 9.68557118351 With tank: 19.44, 9.28247100185 With tank: 19.53, 8.90110311764 With tank: 19.62, 8.54102694231 With tank: 19.71, 8.20143015023 With tank: 19.8, 7.8813140693 With tank: 19.89, 7.57960808839 With tank: 19.98, 7.29523769507 With tank: 20.07, 7.02716257975 With tank: 20.16, 6.77439573013 With tank: 20.25, 6.53601077059 With tank: 20.34, 6.31114235764 With tank: 20.43, 6.09898280627 With tank: 20.52, 5.89877700897 With tank: 20.61, 5.7098169409 With tank: 20.7, 5.53143650944 With tank: 20.79, 5.36300713398 With tank: 20.88, 5.20393418999 With tank: 20.97, 5.05365429058 With tank: 21.06, 4.91163328909 With tank: 21.15, 4.77736482817 With tank: 21.24, 4.65036930643 With tank: 21.33, 4.53019306444 With tank: 21.42, 4.41640770516 With tank: 21.51, 4.30860944437 With tank: 21.6, 4.20641843372 With tank: 21.69, 4.10947802234 With tank: 21.78, 4.01745394307 With tank: 21.87, 3.93003342391 With tank: 21.96, 3.84692423448 With tank: 22.05, 3.76785368254 With tank: 22.14, 3.6925675781 With tank: 22.23, 3.62082918218 With tank: 22.32, 3.55241815638 With tank: 22.41, 3.48712952705 With tank: 22.5, 3.42477267542 With tank: 22.59, 3.3651703627 With tank: 22.68, 3.30815779675 With tank: 22.77, 3.25358174598 With tank: 22.86, 3.20129969597 With tank: 22.95, 3.15117906896 With tank: 23.04, 3.10309648072 With tank: 23.13, 3.05693705371 With tank: 23.22, 3.01259377702 With tank: 23.31, 2.96996691273 With tank: 23.4, 2.92896344621 Outside moment-fit band
Figure 5.2 – Roll response with and without the tank.
Export CSV

Source: [I1]. Chart notes in Appendix A.

Peak roll reduction against alpha Peak roll reduction (%) against Alpha: normalized stiffness (dimensionless). Hull damping 2 %; Hull damping 5 %. Peak roll reduction against alpha 0 20 40 60 80 0.00 0.05 0.10 0.15 0.20 Alpha: normalized stiffness (dimensionless) Peak roll reduction (%) Hull damping 2 % Hull damping 2 %: 0.02, 24.2533874028 Hull damping 2 %: 0.05, 46.1131587008 Hull damping 2 %: 0.1, 61.3708265831 Hull damping 2 %: 0.15, 65.9955703766 Hull damping 2 %: 0.2, 67.1972659743 Hull damping 5 % Hull damping 5 %: 0.02, 10.4739692338 Hull damping 5 %: 0.05, 23.2862649764 Hull damping 5 %: 0.1, 37.8622654351 Hull damping 5 %: 0.15, 45.5813812497 Hull damping 5 %: 0.2, 48.6884412365
Figure 5.3 – Peak roll reduction against alpha.
Export CSV

Source: [I1]. Chart notes in Appendix A.

5.2 Long-period penalty

Slow water transfer reduces the effective hull restoring. In the slow-forcing limit, the roll ratio approaches 1/(1−α). At alpha 0.05, that limit gives 5.3 % more roll.

At 60 s forcing and 18 s hull period with 2 % hull damping, there is 6.0 % more roll at alpha 0.05 and 29.5 % at alpha 0.20, compared with the 25.0 % slow-forcing limit at alpha 0.20, from 1/(1−α). The slow-forcing limit understates the penalty at 60 s. A near-resonance reduction does not remove this penalty. The comparison is recorded in [I1].

6 Validation and benchmark

The model's stated moment fit and the mathematical hand checks address different quantities. The moment fit has 4.3 % RMS error for forcing periods of 20 s and longer; it degrades below about 16 s for a reason not established [R1].

No tank-on and tank-off real-vessel comparison establishes these reductions. No full-scale roll reduction has been calculated here.

Alpha = 0 gives zero reduction, or 0 %. An undamped box hand check copies the model's own moment formula, so it checks arithmetic and the coupling denominator, not the physics of the moment model. It also checks both natural frequencies [I5].

For that mathematical check, each leg measures 2 m by 1 m, with 1 m depth and 1 m offset. The conduit has 1 m² area and 1 m effective length. Fluid density is 1 kg/m³; gravity is 1 m/s².

The hand calculation gives Kₛ = 53/6 N m/rad and H = 359/24 N m/rad at 0.5 rad/s. At alpha 0.1, the response is 2120/1231 times normalized forcing, with no units [I5].

7 Limitations

The model's stated moment fit does not validate coupled hull reduction.

The reductions are screening estimates for generic hulls, with no real-hull evidence; the missing comparison is described in Section 6.

8 Conclusions and next steps

The peak reduction depends on the assumed hull damping and alpha; the separate peak comparisons are shown in Section 5 and Appendix A. The near-resonance reduction does not remove the long-period penalty in Section 5.2.

Calibration transfer and the bare-roll reference remain ASSUMED. The missing real-vessel tank-on and tank-off comparison in Section 6 remains the evidence gap for coupled hull reduction.

9 References

The public model basis and the calculation records identify the inputs, results and mathematical checks used in this report.

9.1 Public references

No external publication is used. The moment-fit statement below comes from the model documentation.

9.2 Data record and builder links

Appendix A Sensitivity matrix

The full matrix retains every calculated hull-period, damping and alpha combination. Table A.1 gives the peak reduction and the coupled peak forcing period [I1].

Hull roll period (s)Hull damping (% of critical)Alpha (1) Peak reduction (%)Coupled peak forcing period (s)
1820.0224.318.1
1820.0546.118.5
1820.1061.419.3
1820.1566.020.4
1820.2067.221.4
1850.0210.518.2
1850.0523.318.4
1850.1037.919.1
1850.1545.620.1
1850.2048.721.3
2120.0220.721.2
2120.0537.821.6
2120.1050.122.5
2120.1555.023.4
2120.2056.924.4
2150.029.021.3
2150.0519.221.6
2150.1029.822.4
2150.1535.223.4
2150.2037.724.5
Table A.1 – Peak reduction sensitivity matrix.
Peak roll reduction against alpha, all twenty cases of Table A.1 Peak roll reduction (%) against Alpha: normalized stiffness (dimensionless). 18 s hull, 2 % damping; 18 s hull, 5 % damping; 21 s hull, 2 % damping; 21 s hull, 5 % damping. Peak roll reduction against alpha, all twenty cases of Table A.1 0 20 40 60 80 0.00 0.05 0.10 0.15 0.20 Alpha: normalized stiffness (dimensionless) Peak roll reduction (%) 18 s hull, 2 % damping 18 s hull, 2 % damping: 0.02, 24.2533874028 18 s hull, 2 % damping: 0.05, 46.1131587008 18 s hull, 2 % damping: 0.1, 61.3708265831 18 s hull, 2 % damping: 0.15, 65.9955703766 18 s hull, 2 % damping: 0.2, 67.1972659743 18 s hull, 5 % damping 18 s hull, 5 % damping: 0.02, 10.4739692338 18 s hull, 5 % damping: 0.05, 23.2862649764 18 s hull, 5 % damping: 0.1, 37.8622654351 18 s hull, 5 % damping: 0.15, 45.5813812497 18 s hull, 5 % damping: 0.2, 48.6884412365 21 s hull, 2 % damping 21 s hull, 2 % damping: 0.02, 20.7168498465 21 s hull, 2 % damping: 0.05, 37.8442868735 21 s hull, 2 % damping: 0.1, 50.1454675827 21 s hull, 2 % damping: 0.15, 54.9527318156 21 s hull, 2 % damping: 0.2, 56.9140276292 21 s hull, 5 % damping 21 s hull, 5 % damping: 0.02, 8.97199678145 21 s hull, 5 % damping: 0.05, 19.1739619659 21 s hull, 5 % damping: 0.1, 29.7642601488 21 s hull, 5 % damping: 0.15, 35.2241116568 21 s hull, 5 % damping: 0.2, 37.7402287754
Figure A.1 – Peak roll reduction against alpha, all twenty cases of Table A.1.
Export CSV

Source: [I1]. Chart notes in Appendix A.

Coupled peak forcing period against alpha, all twenty cases of Table A.1 Coupled peak forcing period (s) against Alpha: normalized stiffness (dimensionless). 18 s hull, 2 % damping; 18 s hull, 5 % damping; 21 s hull, 2 % damping; 21 s hull, 5 % damping. Coupled peak forcing period against alpha, all twenty cases of Table A.1 0 5 10 15 20 25 0.00 0.05 0.10 0.15 0.20 Alpha: normalized stiffness (dimensionless) Coupled peak forcing period (s) 18 s hull, 2 % damping 18 s hull, 2 % damping: 0.02, 18.1492 18 s hull, 2 % damping: 0.05, 18.4666 18 s hull, 2 % damping: 0.1, 19.3162 18 s hull, 2 % damping: 0.15, 20.3761 18 s hull, 2 % damping: 0.2, 21.4491 18 s hull, 5 % damping 18 s hull, 5 % damping: 0.02, 18.1827 18 s hull, 5 % damping: 0.05, 18.4426 18 s hull, 5 % damping: 0.1, 19.0891 18 s hull, 5 % damping: 0.15, 20.0849 18 s hull, 5 % damping: 0.2, 21.3182 21 s hull, 2 % damping 21 s hull, 2 % damping: 0.02, 21.2234 21 s hull, 2 % damping: 0.05, 21.6369 21 s hull, 2 % damping: 0.1, 22.4843 21 s hull, 2 % damping: 0.15, 23.4335 21 s hull, 2 % damping: 0.2, 24.4456 21 s hull, 5 % damping 21 s hull, 5 % damping: 0.02, 21.2659 21 s hull, 5 % damping: 0.05, 21.6484 21 s hull, 5 % damping: 0.1, 22.4496 21 s hull, 5 % damping: 0.15, 23.4159 21 s hull, 5 % damping: 0.2, 24.493 20 s lower edge of moment-fit band
Figure A.2 – Coupled peak forcing period against alpha, all twenty cases of Table A.1, with the 20 s lower edge of the moment-fit band drawn.
Export CSV

Source: [I1]. Chart notes in Appendix A.

In this case (18 s, alpha 0.05), hull damping roughly halves the benefit (ratio 0.505). The ratio of the 5 % benefit to the 2 % benefit ranges from 0.43 to 0.72 across the matrix. For alpha 0.02, 0.05, 0.10, 0.15, 0.20 respectively, the ratios are 18 s: 0.43, 0.505, 0.62, 0.69, 0.72; 21 s: 0.43, 0.51, 0.59, 0.64, 0.66. These comparisons rescale forcing between damping groups and therefore change the tank amplitude [I1].

  1. The wave-period chart shades sampled forcing periods below 20 s, outside the model's stated moment-fit band. The 18 s sweep starts at 12.6 s; the band also excludes parts of the 21 s sweep [I1], [R1].
  2. All charts select existing calculated samples without interpolation or new cases. CSV contains each plotted series point; hover or focus points for values and use checkboxes to toggle series. The static SVG retains axes, units, legend and plotted samples for printing [I4].
  3. Reference tank geometry and calibration transfer are assumed; no actual hull geometry is supplied. Hull outline and conduit height are symbolic; widths, depths and centroid offsets use the recorded dimensions [I1].

Appendix B Review status

Calculation records, source links and reproduction instructions are identified in [I4].

AI generated the script, calculations, tests and draft text. Engineering checks and acceptance remain pending. P.E. sign-off remains pending; no engineer signature is asserted.

Appendix C Revision history

RevisionDateDescriptionPrepared / checked
Initial2026-10-24Generic hull screening estimate added to distinguish model predictions from real-hull evidence.AI-drafted; engineering check pending
Clarification2026-10-25Damping basis, assumptions and validity limits clarified; numeric output stabilized and unpublished comparison removed.AI-drafted; engineering check pending
Interactive summary2026-10-25Input-driven tank section, interactive charts and matching CSV exports added; calculated values retained and limits placed before method.AI-drafted; engineering check pending
Report layout2026-10-25Engineering reporting layout applied to presentation: numbered sections, input table, dimensioned section, figure captions and appendices. Calculated values, claims and conclusions retained.AI-drafted; engineering check pending
Summary and chart clarification2026-10-25Earlier headline clarification recorded: peak roll reduction estimates refer to an 18 s hull roll period, with separate 2 % and 5 % damping cases. Moment-fit provenance and extrapolation, slow-forcing limit, tuning basis, symbols and chart scales clarified; calculation data retained.AI-drafted; engineering check pending
Publication layout2026-10-26Source links, visible revision history, schematic labels and chart legend corrected; repeated cross-references consolidated. Calculated values retained.AI-drafted; engineering check pending
R42026-10-26summary chart and 3D schematic, appendix plotsAI-drafted; engineering check pending
Table C.1 – Revision history.